VW Passat repair

+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
- 16. Body
   + 16.1. General information
   16.2. Care of a body
   - 16.3. Insignificant damages of a body
      16.3.1. Processing of scratches
      16.3.2. Repair of dents in a body design
      16.3.3. Repair of the rusted openings or holes in a body design
      16.3.4. Shpatlevka and body painting
   16.4. Considerable damages of a body
   16.5. Moldings, facing of wheel niches
   + 16.6. Cowl elements
   16.7. Forward and back bumpers
   16.8. Forward cross-section beam of a body
   16.9. Forward wing
   + 16.10. Luggage carrier elements
   + 16.11. Elements of a back door (cars with a body the versatile person)
   16.12. Hinges and locks
   16.13. Elimination of jingle of doors
   + 16.14. Elements of a forward door
   + 16.15. Elements of a back door
   16.16. Internal rear-view mirror
   16.17. Central console
   + 16.18. Combination of devices
   16.19. The receiver with coding system
   16.20. Perchatochny box
   16.21. Dashboard
   + 16.22. Forward seats
   + 16.23. Back sitting
   + 16.24. Seat belts
+ 17. Electric circuits

85288f2d виза в китай в санкт-петербурге

Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Body>> Insignificant damages of a body>> Shpatlevka and body painting
At performance of shpatlevochny works it is necessary to have a wide flexible plastic or nylon shpatel. Shpatlevka alignment on the damaged site of a body make so that to form it demanded and smoothness. As soon as it was possible to achieve approximately a demanded contour, stop to smooth down a shpatlevka a shpatel as at too long smoothing down it will start to harden, stick on a shpatel and to roll down. Drawing of the subsequent, thinner layer of a shpatlevka should be carried out after drying of the previous layer and so until level of a shpatlevka will not start to act slightly over level of a processed site. After shpatlevka hardening it is necessary to remove its surplus with a metal scraper or a file. Further processing carry out, using an emery paper set. Begin processing with use of a coarse-grained emery paper and further gradually pass to the fine-grained. The emery paper should be fixed on flat wooden whetstone to achieve the most equal processed surface. At a finishing stage of polishing it is necessary to moisten a waterproof emery paper with water periodically. It gives to a processed surface special smoothness. The Zashpatlevanny dent should appear surrounded on perimeter a layer of pure metal. For removal from the processed site of a dust and fats wash out it water and wipe fat-free solution. With a dusting put on a site a thin layer of light soil. It will help to reveal all defects allowed at processing. The found defects level by means of a new layer of a shpatlevka and again process a surface an emery paper. Continue this procedure before receiving an ideal surface.
After that the surface is ready to final painting. Aerosol drawing of paint should be carried out in the warm, dry, windless atmosphere in the absence of a dust. For this purpose it is necessary to moisten a floor of a working platform with water. When coloring of only one panel, other parts of a body should be covered from paint hit on them with the paper attached by a sticky tape. Before first coat drawing, взболтайте capacity, put a first coat on a trial surface and achieve that it laid down evenly. Achieve a thick layer of a first coat drawing of several thin layers. Polish the grounded surface a waterproof emery paper. Thus do not forget to sprinkle ground area water and periodically to moisten with water an emery paper. Before further coloring dry up a processed site. Drawing of a paint coat is carried out by a spray. The thickness of a paint coat is reached by drawing of several thin layers. Coloring is necessary for beginning from the center of painted area and to move to edges back and forth motions until all painted surface, and also about 20 mm round it will not be painted. A protective film and paper remove through 10–15 mines after drawing of the last paint coat. Give the chance to fresh paint to harden within at least two weeks, then by means of an obnovitel of paint or thin abrasive polishing paste level edges of the painted area to level of old paint. Polish a surface.