VW Passat repair

+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
- 10. Suspension brackets
   - 10.1. Forward suspension bracket
      10.1.1. Technical characteristics
      10.1.2. General data
      10.1.3. Amortizatorny rack of a forward suspension bracket
      10.1.4. Rotary fist
      10.1.5. Bearing of a forward wheel
      10.1.6. Cross-section lever
      10.1.7. Stabilizer of cross-section stability
      10.1.8. Corners of installation of wheels
   + 10.2. Back suspension bracket
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
+ 16. Body
+ 17. Electric circuits


Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Suspension brackets>> Forward suspension bracket>> Rotary fist

Fig. 10.6. Lower part of a forward suspension bracket: 1–amortization rack; 2–rotary fist; 3–lock ring; 4–nave bearing; 5–nave; 6–washer; 7–самоконтрящаяся nut; 8–ABS sensor rotor; 9–bottom spherical support; 10-lock plate; 11-cross-section lever of a forward suspension bracket; 12-plug of the stabilizer of cross-section stability; 13-connector of the stabilizer of cross-section stability; 14-stabilizer of cross-section stability; 15-back saylentblok of the cross-section lever; 16-forward saylentblok of the cross-section lever; 17-cross-section beam; 18-deflector

Removal of a rotary fist is made in the following order:

Rotary fist 2 (fig. 10.6) remove and establish separately or together with a forward amortizatorny rack.

– remove a decorative cap of a wheel;
– unscrew a nut of the 7th fastening of a nave in situation «the car on wheels»;
– weaken bolts of fastening of a wheel;
– will hang out and fix on basic racks a forward part of the car;
– unscrew bolts of fastening of a wheel and remove a wheel;
– unscrew a nut of fastening of a power shaft and remove a washer;
– remove a support and a brake disk. Using a soft wire, tie up a support to a rack;
– unscrew the deflector 18 and disconnect it from the cross-section lever 11 of a suspension bracket;
– unscrew a nut of the coupling bolt, 9 cross-section levers 11 of a suspension bracket fixing the bottom spherical support to a rotary fist 2;
– note the adjusting provision of a bolt, take a bolt and a pin of the bottom spherical support from a rotary fist for what wring out the cross-section lever from a rotary fist down. At emergence of difficulties with removal of the cross-section lever insert between the lever and a car body mount and squeeze out the lever;

At carrying out work try not to damage a protective cover of a spherical support.

– disconnect steering draft from a rotary fist;
– disconnect a connector of the stabilizer of cross-section stability from the cross-section lever;
– if the rotary fist acts in film separately from an amortizatorny rack 1, note the mutual provision of a rack and a rotary fist. Note the top and bottom bolts of fastening of a rotary fist to a rack correctly to establish them on former places as the corner of disorder of a wheel depends on their situation, and unscrew bolts. Using the lever, take a rack from a rotary fist.
At removal of a rotary fist together with a rack отвернтите a nut of the top fastening of a rack. If the cylindrical spring of a suspension bracket is still compressed, establish a jack under a rotary fist to support weight of a rotary fist and a rack, and after a detachment of the top part of a rack, lower a jack to release a cylindrical spring.
Remove a rotary fist, at the same time removing it from a power shaft. If necessary, using a stripper, squeeze out a power shaft from a wheel nave.
Installation of a rotary fist carry out to sequences, return to removal.
Check correctness of installation of bolts of fastening of a rotary fist to a rack.
Nuts of fastening of a power shaft and the stabilizer tighten only in situation «the car on wheels».