VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
- 8. Transmission
   + 8.1. Mechanical transmission
   - 8.2. Automatic transmission
      8.2.1. Specifications and characteristics
      8.2.2. General information
      8.2.3. Maintenance of an automatic transmission
      8.2.4. Governing bodies
      8.2.5. Transmission maintenance
      8.2.6. Removal and transmission installation
      8.2.7. Hydrotransformer epiploon
      8.2.8. Search of malfunctions
   + 8.3. Distinctive features of transmission of cars with a full drive of Passat Syncro
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
+ 16. Body
+ 17. Electric circuits



85288f2d

Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Transmission>> Automatic transmission>> Governing bodies
The lever of the selector put in action by the driver, is connected by a cable to the gear shifting lever on a transmission. The lever of gear shifting of transmission in turn puts in action the valve of a manual drive in the block of valves.
Blocking of transfer is provided with the block of electronic control by transmission. The control unit includes and disconnects the traction relay on the selector lever, preventing lever moving from the provisions Park and Neutral under certain conditions.
The sensor of inclusion of the low gear, built in a cable of management of a butterfly valve, gives a signal on transmission. This signal is used by the electronic control unit for a choice of the most optimum transfer.

Selector lever

Fig. 8.69. The mechanism of the selector of automatic transmission (the axis of the lever and the left lower part of the mechanism are lowered to show a persistent plate of the automatic zamkovy device: 1–traction relay of the zamkovy device; 2–socket; 3– clamp; 4–pusher; 5–inclusion button; 6–selector lever; 7–persistent plate


The selector lever assembled, including the traction relay of blocking of the included transfer, is shown on fig. 8.69 . By pressing of the trigger button on the lever the pusher located in the lever is put in action. The unblocking of the mechanism is thus carried out and possibility of inclusion of other transfer is provided.

Cable of the selector of transfers

Fig. 8.70. Selector mechanism: 1–a pin for fastening of a cable of the selector


The cable of the selector fastens from the interior of the selector mechanism for a finger and is fixed by a bracket. The site of a finger is shown on fig. 8.70 . Before installation put on a cable tip a thin layer of greasing.
On the other hand the cable incorporates to the lever of gear shifting of transmission by means of a special bolt with a fillet, and the cover of a cable fastens a bracket to an arm on a transmission case. From transmission before installation also it is required to grease a cable tip slightly.

Cable adjustment
Adjustment of a cable carry out in the following order:
transfer the selector lever to the situation Park;
weaken a bolt with a fillet, a fixing cable of the selector to the gear shifting lever on a transmission;
be convinced that the mechanism of transmission provided the demanded situation Park, on what will specify operation of the automatic zamkovy device;
tighten a bolt.

Automatic zamkovy device

Fig. 8.71. Zamkovoye device: 1–inclusion button; 2–selector lever; 3–persistent plate; 4–traction relay; 5–pusher of the lever of the selector


The automatic zamkovy device (fig. 8.71) is a part of the mechanism of the selector of transfers.
Operation of the zamkovy device is reached at turning on of the traction relay of the zamkovy device by the electronic control unit. The traction relay turns a persistent plate, blocking a pusher of the lever of the selector. Mechanism liberation is thus excluded from the situation which is set by a clamp of the selector.
The control unit turns on the traction relay every time when the lever is established in the provisions Park or Neutral. By pressing of a pedal of a brake the control unit the signal of shutdown of the traction relay then the lever of the selector can move to other situation arrives.
In the traction relay of the zamkovy device there are the longitudinal grooves intended for fastening providing adjustment of position of the traction relay.

Fig. 8.72. For check of correctness of position of the traction relay of the zamkovy device check a gap between a persistent plate and a pusher of the lever of the selector. The size "a" should correspond 0,3 mm


Disconnect the socket and at the disconnected traction relay adjust its situation (fig. 8.72) . After adjustment check operation of the zamkovy device in the provisions Park or Neutral, and also operation of the lever of the selector in all provisions.

       NOTE
Before a wraparound put on screws of fastening of the traction relay a thin layer of the regulated greasing.